View M48T128Y-70PM1_5067244.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

M48T128Y M48T128V
5.0 or 3.3 V, 1 Mbit (128 Kb x 8) TIMEKEEPER(R) SRAM
Features
Integrated, ultra low power SRAM, real-time clock, power-fail control circuit, battery, and crystal BCD coded year, month, day, date, hours, minutes, and seconds Automatic power-fail chip deselect and WRITE protection WRITE protect voltages (VPFD = power-fail deselect voltage): - M48T128Y: VCC = 4.5 to 5.5 V 4.1 V VPFD 4.5 V - M48T128V: VCC = 3.0 to 3.6 V 2.7 V VPFD 3.0 V (contact the ST sales office for availability) Conventional SRAM operation; unlimited WRITE cycles Software-controlled clock calibration for high accuracy applications 10 years of data retention and clock operation in the absence of power Self-contained battery and crystal in the DIP package Pin and function compatible with JEDEC standard 128 K x 8 SRAMs RoHS compliant - Lead-free second level interconnect
32 1

PMDIP32 module (PM)

June 2010
Doc ID 5746 Rev 6
1/23
www.st.com 1
Contents
M48T128Y, M48T128V
Contents
1 2 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Operation modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1 2.2 2.3 READ mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 WRITE mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Data retention mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3
Clock operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.1 3.2 3.3 3.4 3.5 Reading the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Stopping and starting the oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Calibrating the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 VCC noise and negative going transients . . . . . . . . . . . . . . . . . . . . . . . . . 14
4 5 6 7 8 9
Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 DC and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Environmental information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2/23
Doc ID 5746 Rev 6
M48T128Y, M48T128V
List of tables
List of tables
Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Table 10. Table 11. Table 12. Table 13. Table 14. Signal names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 READ mode AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 WRITE mode AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Operating and AC measurement conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 DC characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Power down/up AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Power down/up trip points DC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 PMDIP32 - 32-pin plastic module DIP, package mechanical data. . . . . . . . . . . . . . . . . . . 19 Ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Doc ID 5746 Rev 6
3/23
List of figures
M48T128Y, M48T128V
List of figures
Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. Figure 9. Figure 10. Figure 11. Figure 12. Logic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 DIP connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 READ mode AC waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 WRITE enable controlled, WRITE AC waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Chip enable controlled, WRITE AC waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Crystal accuracy across temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Clock calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Supply voltage protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 AC testing load circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Power down/up mode AC waveforms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Recycling symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4/23
Doc ID 5746 Rev 6
M48T128Y, M48T128V
Description
1
Description
The M48T128Y/V TIMEKEEPER(R) RAM is a 128 Kb x 8 non-volatile static RAM and realtime clock. The special DIP package provides a fully integrated battery-backed memory and real-time clock solution. The M48T128Y/V directly replaces industry standard 128 Kb x 8 SRAM. It also provides the non-volatility of Flash without any requirement for special WRITE timing or limitations on the number of WRITEs that can be performed. The 32-pin, 600 mil DIP hybrid houses a controller chip, SRAM, quartz crystal, and a long-life lithium button cell in a single package. Figure 1. Logic diagram
VCC
17 A0-A16 W E G M48T128Y M48T128V
8 DQ0-DQ7
VSS
AI02244
Table 1.
Signal names
A0-A16 DQ0-DQ7 E G W VCC VSS NC Address inputs Data inputs / outputs Chip enable Output enable WRITE enable Supply voltage Ground Not connected internally
Doc ID 5746 Rev 6
5/23
Description Figure 2. DIP connections
NC A16 A14 A12 A7 A6 A5 A4 A3 A2 A1 A0 DQ0 DQ1 DQ2 VSS 1 32 2 31 30 3 29 4 28 5 27 6 26 7 8 M48T128Y 25 9 M48T128V 24 23 10 22 11 21 12 20 13 19 14 18 15 17 16 VCC A15 NC W A13 A8 A9 A11 G A10 E DQ7 DQ6 DQ5 DQ4 DQ3
M48T128Y, M48T128V
AI02245
Figure 3.
Block diagram
OSCILLATOR AND CLOCK CHAIN 32,768 Hz CRYSTAL POWER
8x8 TIMEKEEPER REGISTERS A0-A16
131,064 x 8 SRAM ARRAY LITHIUM CELL VOLTAGE SENSE AND SWITCHING CIRCUITRY VPFD
DQ0-DQ7
E W G
VCC
VSS AI01804
6/23
Doc ID 5746 Rev 6
M48T128Y, M48T128V
Operation modes
2
Operation modes
Figure 3 on page 6 illustrates the static memory array and the quartz controlled clock oscillator. The clock locations contain the year, month, date, day, hour, minute, and second in 24 hour BCD format. Corrections for 28, 29 (leap year - valid until 2100), 30, and 31 day months are made automatically. Byte 1FFF8h is the clock control register. This byte controls user access to the clock information and also stores the clock calibration setting. The seven clock bytes (1FFFFh - 1FFF8h) are not the actual clock counters, they are memory locations consisting of BiPORTTM READ/WRITE memory cells within the static RAM array. The M48T128Y/V includes a clock control circuit which updates the clock bytes with current information once per second. The information can be accessed by the user in the same manner as any other location in the static memory array. The M48T128Y/V also has its own power-fail detect circuit. This control circuitry constantly monitors the supply voltage for an out of tolerance condition. When VCC is out of tolerance, the circuit write protects the TIMEKEEPER(R) register data and external SRAM, providing data security in the midst of unpredictable system operation. As VCC falls below the battery backup switchover voltage (VSO), the control circuitry automatically switches to the battery, maintaining data and clock operation until valid power is restored. Table 2.
Mode Deselect WRITE READ READ Deselect Deselect VSO to VPFD (min)(1) VSO(1) 4.5 to 5.5 V or 3.0 to 3.6 V
Operating modes
VCC E VIH VIL VIL VIL X X G X X VIL VIH X X W X VIL VIH VIH X X DQ0-DQ7 High Z DIN DOUT High Z High Z High Z Power Standby Active Active Active CMOS standby Battery backup mode
1. See Table 11 on page 18 for details.
Note:
X = VIH or VIL; VSO = battery backup switchover voltage.
Doc ID 5746 Rev 6
7/23
Operation modes
M48T128Y, M48T128V
2.1
READ mode
The M48T128Y/V is in the READ mode whenever W (WRITE enable) is high and E (chip enable) is low. The unique address specified by the 17 address inputs defines which one of the 131,072 bytes of data is to be accessed. Valid data will be available at the data I/O pins within tAVQV (address access time) after the last address input signal is stable, providing the E and G access times are also satisfied. If the E and G access times are not met, valid data will be available after the latter of the chip enable access times (tELQV) or output enable access time (tGLQV). The state of the eight three-state data I/O signals is controlled by E and G. If the outputs are activated before tAVQV, the data lines will be driven to an indeterminate state until tAVQV. If the address inputs are changed while E and G remain active, output data will remain valid for tAXQX (output data hold time) but will go indeterminate until the next address access.
Figure 4.
READ mode AC waveforms
tAVAV A0-A16 tAVQV tELQV E tELQX tGLQV G tGLQX DQ0-DQ7 DATA OUT
AI01197
VALID tAXQX tEHQZ
tGHQZ
Note: Table 3.
WE = High. READ mode AC characteristics
M48T128Y M48T128V -85 Max Min 85 70 70 40 5 5 25 25 10 5 5 5 30 30 85 85 55 Max ns ns ns ns ns ns ns ns ns Unit Parameter(1) Min
Symbol
-70
tAVAV tAVQV tELQV tGLQV tELQX(2) tGLQX(2) tEHQZ(2) tGHQZ(2) tAXQX
2. CL = 5 pF.
READ cycle time Address valid to output valid Chip enable low to output valid Output enable low to output valid Chip enable low to output transition Output enable low to output transition Chip enable high to output Hi-Z Output enable high to output Hi-Z Address transition to output transition
70
1. Valid for ambient operating temperature: TA = 0 to 70 C; VCC = 4.5 to 5.5 V or 3.0 to 3.6 V (except where noted).
8/23
Doc ID 5746 Rev 6
M48T128Y, M48T128V
Operation modes
2.2
WRITE mode
The M48T128Y/V is in the WRITE mode whenever W (WRITE enable) and E (chip enable) are low state after the address inputs are stable. The start of a WRITE is referenced from the latter occurring falling edge of W or E. A WRITE is terminated by the earlier rising edge of W or E. The addresses must be held valid throughout the cycle. E or W must return high for a minimum of tEHAX from chip enable or tWHAX from WRITE enable prior to the initiation of another READ or WRITE cycle. Data-in must be valid tDVWH prior to the end of WRITE and remain valid for tWHDX afterward. G should be kept high during WRITE cycles to avoid bus contention; although, if the output bus has been activated by a low on E and G a low on W will disable the outputs tWLQZ after W falls. Figure 5. WRITE enable controlled, WRITE AC waveform
tAVAV A0-A16 VALID tAVWH tAVEL E tWLWH tAVWL W tWLQZ tWHDX DQ0-DQ7 DATA INPUT tDVWH AI02382 tWHQX tWHAX
Figure 6.
Chip enable controlled, WRITE AC waveforms
tAVAV A0-A16 VALID tAVEH tAVEL E tAVWL W tEHDX DQ0-DQ7 DATA INPUT tDVEH AI02383 tELEH tEHAX
Doc ID 5746 Rev 6
9/23
Operation modes Table 4. WRITE mode AC characteristics
M48T128Y Symbol Parameter(1) Min tAVAV tAVWL tAVEL tWLWH tELEH tWHAX tEHAX tDVWH tDVEH tWHDX tEHDX tWLQZ(2)(3) tAVWH tAVEH tWHQX
(2)(3)
M48T128Y, M48T128V
M48T128V -85 Unit Max ns ns ns ns ns ns ns ns ns ns ns 30 70 70 5 ns ns ns ns
-70 Max Min 85 0 0 60 65 5 15 35 35 5 15 25 60 60 5
WRITE cycle time Address valid to WRITE enable low Address valid to chip enable low WRITE enable pulse width Chip enable low to chip enable 1 high WRITE enable high to address transition Chip enable high to address transition Input valid to WRITE enable high Input valid to chip enable high WRITE enable high to input transition Chip enable high to input transition WRITE enable low to output Hi-Z Address valid to WRITE enable high Address valid to chip enable high WRITE enable high to output transition
70 0 0 50 55 5 10 30 30 5 10
1. Valid for ambient operating temperature: TA = 0 to 70 C; VCC = 4.5 to 5.5 V or 3.0 to 3.6 V (except where noted). 2. CL = 5 pF. 3. If E goes low simultaneously with W going low, the outputs remain in the high impedance state.
2.3
Data retention mode
With valid VCC applied, the M48T128Y/V operates as a conventional BYTEWIDETM static RAM. Should the supply voltage decay, the RAM will automatically power-fail deselect, write protecting itself when VCC falls within the VPFD (max), VPFD (min) window. All outputs become high impedance, and all inputs are treated as "Don't care."
Note:
A power failure during a WRITE cycle may corrupt data at the currently addressed location, but does not jeopardize the rest of the RAM's content. At voltages below VPFD (min), the user can be assured the memory will be in a write protected state, provided the VCC fall time is not less than tF. The M48T128Y/V may respond to transient noise spikes on VCC that reach into the deselect window during the time the device is sampling VCC. Therefore, decoupling of the power supply lines is recommended. When VCC drops below VSO, the control circuit switches power to the internal battery, preserving data and powering the clock. The internal energy source will maintain data in the M48T128Y/V for an accumulated period of at least 10 years at room temperature. As system power rises above VSO, the battery is disconnected, and the power supply is switched to external VCC. Deselect continues for tREC after VCC reaches VPFD (max).
10/23
Doc ID 5746 Rev 6
M48T128Y, M48T128V
Clock operations
3
3.1
Clock operations
Reading the clock
Updates to the TIMEKEEPER(R) registers should be halted before clock data is read to prevent reading data in transition. The BiPORTTM TIMEKEEPER cells in the RAM array are only data registers and not the actual clock counters, so updating the registers can be halted without disturbing the clock itself. Updating is halted when a '1' is written to the READ bit, D6 in the control register (1FFF8h). As long as a '1' remains in that position, updating is halted. After a halt is issued, the registers reflect the count; that is, the day, date, and time that were current at the moment the halt command was issued. All of the TIMEKEEPER registers are updated simultaneously. A halt will not interrupt an update in progress. Updating is within a second after the bit is reset to a '0.'
3.2
Setting the clock
Bit D7 of the control register (1FFF8h) is the WRITE bit. Setting the WRITE bit to a '1,' like the READ bit, halts updates to the TIMEKEEPER registers. The user can then load them with the correct day, date, and time data in 24-hour BCD format (see Table 5 on page 12). Resetting the WRITE bit to a '0' then transfers the values of all time registers 1FFFFh1FFF9h to the actual TIMEKEEPER counters and allows normal operation to resume. After the WRITE bit is reset, the next clock update will occur one second later.
3.3
Stopping and starting the oscillator
The oscillator may be stopped at any time. If the device is going to spend a significant amount of time on the shelf, the oscillator can be turned off to minimize current drain on the battery. The STOP bit is located at bit D7 within 1FFF9h. Setting it to a '1' stops the oscillator. The M48T128Y/V is shipped from STMicroelectronics with the STOP bit set to a '1.' When reset to a '0,' the M48T128Y/V oscillator starts after one second.
Doc ID 5746 Rev 6
11/23
Clock operations Table 5.
Address D7 1FFFFh 1FFFEh 1FFFDh 1FFFCh 1FFFBh 1FFFAh 1FFF9h 1FFF8h 0 0 0 0 0 ST W R D6 D5 D4 D3 D2 D1 Year 10 M Month Date 0 Day Hours Minutes Seconds Calibration D0 10 years 0 0 FT 0 0
M48T128Y, M48T128V Register map
Data Function/range BCD format Year Month Date Day Hours Minutes Seconds Control 00-99 01-12 01-31 01-07 00-23 00-59 00-59
10 date 0 0
10 hours 10 minutes 10 seconds S
Keys: S = SIGN bit R = READ bit W = WRITE bit ST = STOP bit 0 = Must be set to '0' Z = '0' and are Read only Y = '1' or '0'
3.4
Calibrating the clock
The M48T128Y/V is driven by a quartz controlled oscillator with a nominal frequency of 32,768 Hz. The devices are factory calibrated at 25 C and tested for accuracy. Clock accuracy will not exceed 35 ppm (parts per million) oscillator frequency error at 25 C, which equates to about 1.53 minutes per month. When the Calibration circuit is properly employed, accuracy improves to better than +1/-2 ppm at 25 C. The oscillation rate of crystals changes with temperature (see Figure 7 on page 13). The M48T128Y/V design employs periodic counter correction. The calibration circuit adds or subtracts counts from the oscillator divider circuit at the divide by 128 stage, as shown in Figure 8 on page 13. The number of times pulses are blanked (subtracted, negative calibration) or split (added, positive calibration) depends upon the value loaded into the five calibration bits found in the control register. Adding counts speeds the clock up, subtracting counts slows the clock down. The calibration bits occupy the five lower order bits (D4-D0) in the control register 1FFF8h. These bits can be set to represent any value between 0 and 31 in binary form. Bit D5 is a sign bit; '1' indicates positive calibration, '0' indicates negative calibration. Calibration occurs within a 64 minute cycle. The first 62 minutes in the cycle may, once per minute, have one second either shortened by 128 or lengthened by 256 oscillator cycles. If a binary '1' is loaded into the register, only the first 2 minutes in the 64 minute cycle will be modified; if a binary 6 is loaded, the first 12 will be affected, and so on. Therefore, each calibration step has the effect of adding 512 or subtracting 256 oscillator cycles for every 125, 829, 120 actual oscillator cycles, that is +4.068 or -2.034 ppm of adjustment per calibration step in the calibration register. Assuming that the oscillator is running at exactly 32,768 Hz, each of the 31 increments in the calibration byte would represent +10.7 or -5.35 seconds per month which corresponds to a total range of +5.5 or -2.75 minutes per month.
12/23
Doc ID 5746 Rev 6
M48T128Y, M48T128V
Clock operations
One method is available for ascertaining how much calibration a given M48T128Y/V may require. This involves setting the clock, letting it run for a month and comparing it to a known accurate reference and recording deviation over a fixed period of time. Calibration values, including the number of seconds lost or gained in a given period, can be found in the STMicroelectronics application note, "TIMEKEEPER calibration." This allows the designer to give the end user the ability to calibrate the clock as the environment requires, even if the final product is packaged in a non-user serviceable enclosure. The designer could provide a simple utility that accesses the calibration byte. For example, a deviation of 21 seconds slow over a period of 30 days would indicate a -8 ppm oscillator frequency error, requiring a +2(WR100010) to be loaded into the calibration byte for correction. Figure 7. Crystal accuracy across temperature
ppm 20
0
-20
-40 F = -0.038 ppm (T - T )2 10% 0 F C2 T0 = 25 C -80
-60
-100 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 C
AI02124
Figure 8.
Clock calibration
NORMAL
POSITIVE CALIBRATION
NEGATIVE CALIBRATION AI00594B
Doc ID 5746 Rev 6
13/23
Clock operations
M48T128Y, M48T128V
3.5
VCC noise and negative going transients
ICC transients, including those produced by output switching, can produce voltage fluctuations, resulting in spikes on the VCC bus. These transients can be reduced if capacitors are used to store energy which stabilizes the VCC bus. The energy stored in the bypass capacitors will be released as low going spikes are generated or energy will be absorbed when overshoots occur. A ceramic bypass capacitor value of 0.1 F (as shown in Figure 9) is recommended in order to provide the needed filtering. In addition to transients that are caused by normal SRAM operation, power cycling can generate negative voltage spikes on VCC that drive it to values below VSS by as much as one volt. These negative spikes can cause data corruption in the SRAM while in battery backup mode. To protect from these voltage spikes, it is recommended to connect a Schottky diode from VCC to VSS (cathode connected to VCC, anode to VSS). Schottky diode 1N5817 is recommended for through hole and MBRS120T3 is recommended for surface mount. Figure 9. Supply voltage protection
VCC VCC
0.1F
DEVICE
VSS
AI02169
14/23
Doc ID 5746 Rev 6
M48T128Y, M48T128V
Maximum ratings
4
Maximum ratings
Stressing the device above the rating listed in the absolute maximum ratings table may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the operating sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Table 6.
Symbol TA TSTG TSLD(1)(2) VIO VCC IO PD
Absolute maximum ratings
Parameter Ambient operating temperature Storage temperature (VCC off, oscillator off) Lead solder temperature for 10 seconds Input or output voltages Supply voltage Output current Power dissipation M48T128Y M48T128V Value 0 to 70 -40 to 85 260 -0.3 to 7 -0.3 to 7 -0.3 to 4.6 20 1 Unit C C C V V V mA W
1. Soldering temperature of the IC leads is to not exceed 260 C for 10 seconds. In order to protect the lithium battery, preheat temperatures must be limited such that the battery temperature does not exceed +85 C. Furthermore, the devices shall not be exposed to IR reflow. 2. For DIP packaged devices, ultrasonic vibrations should not be used for post-solder cleaning to avoid damaging the crystal.
Caution:
Negative undershoots below -0.3 V are not allowed on any pin while in the battery backup mode.
Doc ID 5746 Rev 6
15/23
DC and AC parameters
M48T128Y, M48T128V
5
DC and AC parameters
This section summarizes the operating and measurement conditions, as well as the DC and AC characteristics of the device. The parameters in the following DC and AC characteristic tables are derived from tests performed under the measurement conditions listed in the relevant tables. Designers should check that the operating conditions in their projects match the measurement conditions when using the quoted parameters. Table 7. Operating and AC measurement conditions
Parameter Supply voltage (VCC) Ambient operating temperature (TA) Load capacitance (CL) Input rise and fall times Input pulse voltages Input and output timing ref. voltages M48T128Y 4.5 to 5.5 0 to 70 100 5 0 to 3 1.5 M48T128V 3.0 to 3.6 0 to 70 50 5 0 to 3 1.5 Unit V C pF ns V V
Note:
Output Hi-Z is defined as the point where data is no longer driven. Figure 10. AC testing load circuit
650
DEVICE UNDER TEST
CL = 100pF or 50pF(1)
1.75V
CL includes JIG capacitance
AI03630
1. 50 pF for M48T128V.
Table 8.
Symbol CIN CIO(3)
Capacitance
Parameter(1)(2) Input capacitance Input / output capacitance Min Max 20 20 Unit pF pF
1. Effective capacitance measured with power supply at 5 V. Sampled only, not 100% tested. 2. At 25 C, f = 1 MHz. 3. Outputs deselected.
16/23
Doc ID 5746 Rev 6
M48T128Y, M48T128V Table 9. DC characteristics
M48T128Y Symbol Parameter Test condition(1) Min ILI ILO
(2)
DC and AC parameters
M48T128V -85 Unit Max 2 2 50 4 3 -0.3 2.2 0.4 VCC + 0.3 0.4 2.2 A A mA mA mA V V V V
-70 Max 2 2 95 8 4 -0.3 2.2 0.8 VCC + 0.3 0.4 2.4 Min
Input leakage current Output leakage current Supply current Supply current (standby) TTL Supply current (standby) CMOS Input low voltage Input high voltage Output low voltage Output high voltage
0 V VIN VCC 0 V VOUT VCC Outputs open E = VIH E = VCC - 0.2 V
ICC ICC1 ICC2 VIL VIH VOL VOH
IOL = 2.1 mA IOH = -1 mA
1. Valid for ambient operating temperature: TA = 0 to 70 C; VCC = 4.5 to 5.5 V or 3.0 to 3.6 V (except where noted). 2. Outputs deselected.
Doc ID 5746 Rev 6
17/23
DC and AC parameters Figure 11. Power down/up mode AC waveforms
VCC VPFD (max) VPFD (min) VSS tF tDR
M48T128Y, M48T128V
tREC tFB INPUTS
RECOGNIZED
tRB DON'T CARE
RECOGNIZED
HIGH-Z OUTPUTS VALID VALID
AI03612
Table 10.
Symbol tF
(2)
Power down/up AC characteristics
Parameter(1) VPFD (max) to VPFD (min) VCC fall time VPFD (min) to VSS VCC fall time VPFD (min) to VPFD (max) VCC rise time VSS to VPFD (min) VCC rise time VPFD (max) to inputs recognized Min 300 10 0 1 40 200 Max Unit s s s s ms
tFB(3) tR tRB tREC
1. Valid for ambient operating temperature: TA = 0 to 70 C; VCC = 4.5 to 5.5 V or 3.0 to 3.6 V (except where noted). 2. VPFD (max) to VPFD (min) fall time of less than tF may result in deselection/write protection not occurring until 200 s after VCC passes VPFD (min). 3. VPFD (min) to VSS fall time of less than tFB may cause corruption of RAM data.
Table 11.
Symbol VPFD VSO tDR(3)
Power down/up trip points DC characteristics
Parameter(1)(2) Power-fail deselect voltage M48T128Y M48T128V M48T128Y M48T128V 10 Min 4.1 2.7 Typ 4.35 2.9 3.0 VPFD - 100 mV Max 4.5 3.0 Unit V V V V YEARS
Battery backup switchover voltage Expected data retention time
1. All voltages referenced to VSS. 2. Valid for ambient operating temperature: TA = 0 to 70 C; VCC = 4.5 to 5.5 V or 3.0 to 3.6 V (except where noted). 3. At 25 C; VCC = 0 V.
18/23
Doc ID 5746 Rev 6
M48T128Y, M48T128V
Package mechanical data
6
Package mechanical data
In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK(R) packages, depending on their level of environmental compliance. ECOPACK(R) specifications, grade definitions and product status are available at: www.st.com. ECOPACK(R) is an ST trademark.
Figure 1. PMDIP32 - 32-pin plastic module DIP, package outline
A
A1 S B e3 D e1
L eA
C
N
E
1 PMDIP
Note:
Drawing is not to scale. Table 12.
Symb Typ A A1 B C D E e1 e3 eA L S N 38.1 14.99 3.05 1.91 32 16.00 3.81 2.79 Min 9.27 0.38 0.43 0.20 42.42 18.03 2.29 Max 9.52 - 0.59 0.33 43.18 18.80 2.79 1.5 0.590 0.120 0.075 32 0.630 0.150 0.110 Typ Min 0.365 0.015 0.017 0.008 1.670 0.710 0.090 Max 0.375 - 0.023 0.013 1.700 0.740 0.110
PMDIP32 - 32-pin plastic module DIP, package mechanical data
mm inches
Doc ID 5746 Rev 6
19/23
Environmental information
M48T128Y, M48T128V
7
Environmental information
Figure 12. Recycling symbols
This product contains a non-rechargeable lithium (lithium carbon monofluoride chemistry) button cell battery fully encapsulated in the final product. Recycle or dispose of batteries in accordance with the battery manufacturer's instructions and local/national disposal and recycling regulations. Please refer to the following web site address for additional information regarding compliance statements and waste recycling. Go to www.st.com/nvram, then select "Lithium Battery Recycling" from "Related Topics".
20/23
Doc ID 5746 Rev 6
M48T128Y, M48T128V
Part numbering
8
Part numbering
Table 13.
Example:
Ordering information scheme
M48T 128Y -70 PM 1
Device type M48T
Supply voltage and write protect voltage 128Y = VCC = 4.5 to 5.5 V; VPFD = 4.1 to 4.5 V 128V(1) = VCC = 3.0 to 3.6 V; VPFD = 2.7 to 3.0 V
Speed -70 = 70 ns (128Y) -85 = 85 ns (128V)
Package PM = PMDIP32
Temperature range 1 = 0 to 70C
Shipping method blank = Ecopack(R) package, tubes
1. Contact local ST sales office for availability of 3.3 V version.
For other options, or for more information on any aspect of this device, please contact the ST sales office nearest you.
Doc ID 5746 Rev 6
21/23
Revision history
M48T128Y, M48T128V
9
Revision history
Table 14.
Date Jun-1998 31-Jan-2000 30-Mar-2000 20-Jul-2001 21-Sep-2001 23-May-2002 07-Aug-2002 28-Mar-2003 06-Aug-2004 22-Feb-2005 18-Jun-2010
Document revision history
Revision 1 1.1 1.2 2 2.1 2.2 2.3 3 4 5 6 First issue Calibrating the clock paragraph changed Storage temperature changed (Table 6) Reformatted; temperature information added to tables (Table 8, 9, 3, 4, 10, 11) Corrected speed grade in ordering information Add countries to disclaimer; add marketing status Refine marketing status text v2.2 template applied; test condition updated (Table 11) Reformatted; updated register map (Table 5) IR reflow update (Table 6) Updated Features, Section 4, Table 12, 13; added ECOPACK(R) text to Section 6; added Section 7: Environmental information; reformatted document. Changes
22/23
Doc ID 5746 Rev 6
M48T128Y, M48T128V
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
(c) 2010 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com
Doc ID 5746 Rev 6
23/23

▲Up To Search▲

Price & Availability of M48T128Y-70PM1

	To Download M48T128Y-70PM1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .